Dongguan VILLO Technology Inc.
Li- ion Battery Industry

Industrial Dust Removal In Li- ion Battery Industry

Dust removal solutions in Lithium-ion Battery manufacturing

Lithium-ion battery manufacturing has made significant progress in recent years and has become increasingly important in various emerging markets, such as renewable energy and electric or hybrid automobiles. While the process involved in manufacturing batteries can release particles in the air, which can harm workers, machines and product sustainability.

From the first step Mixing to the last step packing, Villo can provide turnkey dust removal solution for lithium-ion manufacturing:

Industrial Dust Remover In Li- ion Battery Industry

Rolling Process

During rolling process many small powders adhered to the surface of the rollers which needs to be cleaned. The cleanliness of the rollers is necessary for preventing foreign particles from penetrating the substrate material. Roller brush is generally used for cleaning.

In the process, there can be 4 small processes need dust removal:

2.1 Dust removal for pole piece before rolling: the upper and lower two sides of the pole piece material need to be equipped with a multi-point recycling collection system. Set 2pcs dia50mm air inlet on the cover of the brush (Confluence is about φ100mm), since the amount of dust is limited, VJ or model with higher configuration can solve the dust problem well, and explosion-proof requirements are considered in due course.

Model can be selected:

Manual cleaning type VJ-H series dust collector

Self-cleaning type VJF series dust collector

VJFGB explosion type dust collector

2.2 Dust removal for corner cutting: each cutter has a diameter of about φ40, ranging from 2 to 4 (commonly 4 scrapers — 2 for each of the upper and lower rollers). After being put together, the φ75 suction port is enough for dust removal on this position. The suction hood is only equipped on the side of the discharge port, and the diameter of each suction hood is φ75. The cutter dust suction hood is shown in Figure 2.3.3-b, the hood for scrap material suction is under the knife, as shown in Figure 2.5.3-1, and the VMQ system for supporting material receiver is shown in Figure 2.5.3-3, or Figure 2.5.3-4.

Model can be selected:

VMQ receiving machine

2.3 Roller dust removal: Dust collector with hood is the ideal option for the dust generated by the upper and lower roller scrapers. The diameter of each blade hood depends on the length of the roller, and set multiple suction openings will be gathered into a total dust suction port (commonly φ73mm or φ110mm) The scraper suction hood is shown in Figure 2.3.3-c.

Models can be selected:

VJ-H series manual cleaning dust collector

VJF series automatic cleaning dust collector

VJFG series dust collector

VJFGB explosion proof dust collector  (Contact us for proposal making)

2.4 Belt-connecting platform: 20-25mm dust extraction pipe cover will be equipped underneath, sharing a main machine with 2.1) & 2.3).

figure 2
figure 2
figure 2

Winding Machine

Dust source:

Square battery: During the winding process, the main dust generating points are the powder brush and the main shaft winding area. (that is, the pole piece cutting position)

Cylindrical battery: The main dust production points of the cylindrical battery are the powder (or blowing and suction) box, the welding point of the pole lug, and the winding area of the main shaft (that is, the position where the pole piece is cut off), which produces a certain amount of smoke and cutting chips or particles.

Solution: The dust particle size and smoke volume produced by the winding machine are small, and the diameter of the dust removal pipe supporting the machine is small. It is necessary to support a high negative pressure industrial vacuum cleaner. VZ-75 vacuum cleaner / VX-400 and VX-550 vacuum cleaners are optional to ensure debris and fume can be sucked away immediately. The dust-pumping mechanism (powder-pumping box) is directly equipped with a suction tube, which is not visible on the back.

dust removal for winding machine
dust removal for winding machine 2


The manufacturing process starts with mixing process which involves feeding and discharge of ingredients which generates a serious amount of fine powder dust, which is active material (includes: Lithium cobaltate, lithium manganate, lithium nickelate, lithium iron phosphate and negative material graphite) can have risk of explosion.

Considering the feeding and discharge port is open, so a suction hood is necessary for capture dust from the source, thus a dust collector with big air flow can be applied here.

Model selection:

VJFB series explosion proof dust collector

figure 1
figure 1
figure 1

Slitting Process

In the process of slitting with a slitting machine, a lot of excess powder and waste (leftover material) will be incidentally generated. These powders will be left on the slitting machine, affecting the service life of the equipment and the quality of the battery cells. The source of dust is at the position of the cutter:

Dust removal solution for slitting machine: considering the character of the dust, we will recommend to use a medium pressure type dust collector. Since quantity of suction ports on the different slitting machines is different, then the power of selected dust collector equipped will be different accordingly. VJ-2.2H-T is optional for small slitting machine, and VJFG-3.7 and VJFG-5.5 are recommended for those worksite with long distance or high wind speed requirements. Anyway, explosion-proof requirements should be considered in due course.

As for leftovers, our VQG and VCY series material receiving machines are the best partners.

Models to be selected:

VJ-H series manual cleaning dust collector

VJFG series medium pressure dust collector

VJFGB series explosion proof dust collector

VQG series material receiving machine

VCY series material receiving machine

Laser Die-cutting Process

Laser die-cutting, also called laser pole forming. This process is generally located before the slitting of the square battery. The principle is to cut the corners of the pole piece by laser.  During the cutting process, laser fume and waste materials will be generated. Fume and dust must be treated immediately, otherwise the product quality will be affected. Dust removal points include die-cut laser heads, pole piece roller brushes, splice platforms, and air knife at the cutting edge, etc.

Dust removal solution is Specially for the characteristics of the scrap produced by the die-cutting machine (continuous thin strip, segment), it needs to be equipped with a large-capacity collection bag dust collection with explosion proof. User will need to prepare the laser cutting hood for die cutting machine.

Models to be selected:

VJFGB series explosion proof dust collector


Smoke/Dust source:

Dust is produced during the stacking of pole pieces.


The lamination machine is generally equipped with a dust suction port (about φ50mm), and a high negative pressure model is required to ensure that dust and debris are sucked away. If there is no suction port, a side suction cover can be installed near the lamination station, and a suction port of about 50mm is can be connected below the suction cover. The optional models are VX400.VX550,VX850. For those with longer than 5meter belt, VJFG series models would be the ideal option.

For more details, please contact us directly.

lamination 01

Modular Laser Welding

Source of Welding fumes:

Laser welding generates smoke and fumes which contains hazardous contaminants and should be removed instantly.


Welding head is bounded with a ø50 suction nozzle at the side or the welding table is equipped with side suction cover to avoid interference with welding operation. A high negative pressure and explosion-proof type fume extractor would be required to solve the problem. Our VJFCB-1.5 and VJFGB series dust collector is an effective solution. Due to high welding power, large sparks and fast splash, the air speed required would be about 23m/s or greater. Also, we will recommend to use a duster.

modular laser welding
modular 01
modular 03
modular 06
modular 07
modular 10

Tab Welding

Welding Fume Source:

Welding fumes and smoke would generate while performing welding operation on the pole tab.


A ø50 suction nozzle and suction hoods are installed above and below each pole tab welding position to wrap the welding head as much as possible. High negative pressure VJFCB, VJFGB and VXF series is an efficient solution.

For the cylindrical battery pole tab welding, side suction mouth and extended suction nozzle would be required.

tab laser welding

Aluminum Shield Welding

Source of Smoke and fumes:

Welding aluminum alloys produce much more harmful fumes and airborne particles than other materials. As these fumes poses threat to welders, a proper fume extractor should be installed to extract these fumes.


Welding head is bounded with a ø50 suction nozzle at the side or the table should be equipped with a side suction cover to avoid interference with welding operation. A high negative pressure and explosion-proof type fume extractor would be required. Our VJFCB-1.5 and VJFGB series dust collector can efficiently solve the problem. Due to high welding power, large sparks and fast splash, the air speed required would be about 18~25m/s. Also, we will recommend to use a duster.

aluminum shield laser welding
shield laser welding 03
shield laser welding 07